HL-DT-ST DVD GDR8162B DRIVER

What usually happens is the cable is ripped at either edge and the wires there are either damaged or severed, often right at a connector or under it’s cable clamp there, where it’s hard to see – if a wire is severed but it’s ends are touching, the connection is intermittent, rather than being reliable. Solved i need the drivers for Hl-dt-st dvd-rom gdrb instalation. Such opinions may not be accurate and they are to be used at your own risk. There must be a jumper on one of those three pairs of pins. XP doesn’t have the drivers built in for most things that first came out after XP was first released, circa , and it doesn’t have some of the drivers built in for things made before that.

Uploader: Tojagrel
Date Added: 24 September 2006
File Size: 60.91 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 90751
Price: Free* [*Free Regsitration Required]

Make sure that there are no pins on the drive or on the mboard IDE headers that are bent over such that they’re not plugging into the data cable connectors.

Net is the opinions of dvf users. Your drive is an IDE drive.

LG HL-DT-ST dvd-rom GDR8162B Free Driver Download

It was made in August There are two rows of 3 pins on the back of the drive next to the pins for the IDE header. If you have a generic system and have the CD that came hhl-dt-st the mboard, all the necessary drivers are on it.

If it is possible for a data cable connector to plug into a IDE header either way, the striped side of the data cable must be next to the pin one end of the IDE header on all connections.

  AR2413/AR2414 LINUX DRIVER

The side of the data cable that has a colored stripe must be next to the 4 pin power socket.

Solved i need the drivers for Hl-dt-st dvd-rom gdrb instalation. XP has no built in software codec that can read encoded DVDs, such as pre-recorded movies.

If you load drivers from the web, brand name system builders hl-et-st mboard makers often DO NOT have the main chipset drivers listed in the downloads for your model – in that case you must go to the maker of the main chipset’s web site, get the drivers, and load them.

I have discovered I have the same model sitting around. The jumper setting on the back of the drive must be set properly. What the pins are for is stamped into the metal on top of the drive.

Would you use Snapchat filters on your dog? Net and its accuracy. Yes No I don’t have a dog.

Such opinions may not be accurate and they hl-dt-wt to be used at your own risk. You don’t need to install drivers for it. Hl-dh-st must be a jumper on one of those three pairs of pins. That model is relatively old.

Thousands of users waiting to help! Net cannot verify the validity of the statements made on this site. Your drive does not require an 80 wire data cable – a 40 wire one will do – but if it’s on the same data cable as a hard drive that requires an 80 wire data cable, you must use an 80 wire data cable to get the full max burst speed from the hard drive.

If that doesn’t help, you may need to change a setting regarding drive detection – e. Usually the thing that makes them un-usable first is the cheap sleeve bearings in the motor have worn to the point that so much friction is produced in svd bearings that the motor can no longer spin at the minimum 1X legacy audio CD gd8162b, or the motor doesn’t spin at all.

  ASPIRE 1690 ETHERNET DRIVER DOWNLOAD

Try another data cable if in doubt. The computer’s bios MUST be detecting the drive.

[Solved] i need the drivers for Hl-dt-st dvd-rom gdrb instalation

Use Question Form such as ” Why? Over a Month Ago Time Zone: What usually happens is the cable is ripped at either edge and the wires there are either damaged or severed, often right at a connector or under it’s cable clamp there, where it’s hard to see – if a wire is severed but it’s ends are touching, the connection is intermittent, rather than being reliable. Usually the pin one end of the IDE header on the drive is next to the power socket. Default bios settings are usually already set so any drive that is properly connected, and has the proper jumper setting if it’s an IDE drive, will be detected If you think bios settings may have been set wrong, load bios defaults, Save bios settings.

The information on Computing. You must have both a power connector from the power supply and a data cable properly connected to the drive.